X100 Inhibitor X200 Noise Reducer X300 System Cleaner X400 System Restorer X500 Inhibited Antifreeze X700 Sanitiser and Biocide X800 Jetflo Ultimate Cleaner Deposit Remover Leak Sealer Seal X Joint & Leak Sealer
 

Deposit Remover

 
Introduction
 
 
Application
 
 
FAQs
 
 
Safety Information
 
 
 

Sentinel Deposit Remover is a powerful highly active cleaning agent for use in indirect central heating systems.  Suitable for use with all commonly encountered metals and alloys.

  • Heavy duty acid cleaner
  • Powerful magnetite and limescale remover
  • Removes the toughest deposits

Packaging

 

5 litre bottle

Product_depositRemover_300
 
 

Related Downloads

 

Sentinel Deposit Remover is a powerful, highly active cleaning agent for use in indirect central heating systems. It is specifically designed to remove objectionable iron oxide deposits and limescale from heat exchangers, radiators and pipework. Its unique composition allows Sentinel Deposit Remover to act as a complexing and penetrating dispersant under less acidic conditions than other acid based products.

Sentinel Deposit Remover is suitable for use with all commonly encountered metals and alloys. Aluminium may be cleaned, but special precautions must be taken with a maximum cleaning time of 2 hours.

Potable water systems may be cleaned, but must be flushed thoroughly before being returned to service.

Dosage:


A single 5L container of Sentinel Deposit Remover is sufficient to clean a typical domestic system up to 10 radiators. For larger systems, two 5L containers should be used. For faster cleaning, or with heavily fouled equipment, a typical system should also be cleaned with two 5L containers. The main system pump is suitable for circulation throughout the entire system.

Cleaning action is accelerated when the Sentinel Deposit Remover solution is heated and in constant circulation, but the temperature must not exceed 60°C.

In accordance with BS7593:2006, more rapid and effective cleaning will result if Sentinel Deposit Remover is used in conjunction with a power flushing device.

After cleaning, the system should be drained and flushed until the water runs clear, and the pH or conductivity of the flush water matches that of the mains water. On refilling, the system should be treated with Sentinel X100 Inhibitor, or Sentinel X500 Inhibited Antifreeze.

Feeding:


Open Systems: Dose via F&E cistern, via a by-pass feeder or use a Sentinel Dosing Vessel.
Sealed Systems: If the system is empty, add to any convenient point before filling. If full, use a Sentinel Dosing Vessel to inject via the filling loop or other access point.

Physical properties

Appearance: Brown liquid
Odour: Mild
Specific Gravity: 1.17 (20°C)
pH in aqueous solution (5%) : 3.0
Freezing point: -6°C

Product_depositRemover_300
 
 

Related Downloads

 

How do I get Sentinel Deposit Remover into the system?


Sentinel Deposit Remover is a heavy duty cleaner designed to remove scale & oxide deposits from heat exchangers, pipes and radiators and can be dosed via F&E cistern, via a by-pass feeder or use a Sentinel Dosing Vessel. When powerflushing, the product may be applied into the tank of the powerflush machine. Check the machine manufacturer’s instructions.

Is the Sentinel Deposit Remover pH neutral?


No. Sentinel Deposit Remover is mildly acidic and has a pH level of 2-3. No chemical neutralisation is required, but it is important to completely flush the cleaning solution from the system at the end of the cleaning period (max 2 hours). It is recommended to ensure that flushing continues until the pH or conductivity of the flush water matches that of the mains water.

Can Sentinel Deposit Remover be used with aluminium components?

Sentinel Deposit Remover is suitable for use with all commonly encountered metals and alloys including aluminium. However, because of the acidic nature of the product, cleaning/circulating time must be limited to a maximum of 2 hours and the system must be fully flushed with clean water after use.

Product_depositRemover_300
 
 

Related Downloads

 

 

 

 

The information provided below enables compliance with the Control of Substances Hazardous to Health Regulations. A Safety Data Sheet is available upon request.

 

 

Sentinel Deposit Remover
Mild Acid Descaler for Central Heating Systems

 

An aqueous solution of synthetic organic polymers, wetting agents, and organic acid.

Health Hazards

Irritating to eyes.

Handling

Keep out of the reach of children.
Avoid contact with skin and eyes.
Wash out empty container thoroughly with water before disposal.

Storage

Keep container tightly closed.
Store in cool, well ventilated area.

Spillage

Absorb on to inert material and dispose of according to Special Waste Regulations.

Fire/Explosion Risks

Non-flammable.

 

First Aid

Skin Exposure

After contact with skin, wash immediately with plenty of water.
Immediately remove all contaminated clothing.

Eye Exposure

In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.

Ingestion

Rinse mouth with water.
Do NOT induce vomiting!
Seek medical advice.

Product_depositRemover_300
 
 

Related Downloads

 
 
 
 
 
 
Buy Online at Sentinel
 

Find a Stockist

Find a Stockist
 
Town/Postcode : Search
 
 

Featured Product

X100 Inhibitor

Following a recent research

.... study with Installers, we were asked what's inside the bottle that makes Sentinel different from the rest? More

 
 
 
 
 
 
 

Sentinel is recommended by manufacturers including :

/uploadedImages/wwwsentinel-solutionsnet/use_for_library_images/approved_by_images/3_alpha.gif/uploadedImages/wwwsentinel-solutionsnet/use_for_library_images/approved_by_images/2_ariston.gif/uploadedImages/wwwsentinel-solutionsnet/use_for_library_images/approved_by_images/halstead_28.gif/uploadedImages/wwwsentinel-solutionsnet/use_for_library_images/approved_by_images/ideal_28.gif/uploadedImages/wwwsentinel-solutionsnet/use_for_library_images/approved_by_images/1_vokera.gif/uploadedImages/wwwsentinel-solutionsnet/use_for_library_images/approved_by_images/Worcester_28(1).jpg
 
 
 
Sentinel Performance Solutions Ltd | The Heath Business & Technical Park | Runcorn | Cheshire | WA7 4QX | 01928 588 330